CALIBRATION CHECKLIST

Created by ChecklistGuro (https://checklistguro.com)

--- EQUIPMENT IDENTIFICATION & INFORMATION ---
[ ] Equipment Name/Description
[ ] Manufacturer
[ ] Model Number
[ ] Serial Number
[ ] Asset Tag Number
[ ] Date of Last Calibration
[ ] Next Calibration Due Date
[ ] Location (Production Line 1, Production Line 2, Quality Control, Warehouse, Other)
[ ] Any previous issues or notes?

--- ENVIRONMENTAL CONDITIONS ---
[ ] Ambient Temperature (°C)
[ ] Ambient Temperature (°F)
[ ] Relative Humidity (%)
[ ] Air Pressure (kPa)
[ ] Date of Environmental Measurement
[ ] Time of Environmental Measurement
[ ] Notes on Environmental Conditions (e.g., drafts, unusual fluctuations)

--- CALIBRATION STANDARDS ---
[ ] Standard Serial Number
[ ] Standard Uncertainty (k=2)
[ ] Standard Traceability (e.g., NIST, ISO) (NIST, ISO, Other (Specify))
[ ] Traceability Details (Specify originating standard)
[ ] Standard Calibration Due Date
[ ] Standard Calibration Certificate
[ ] Standard Condition (As Received) (Within Tolerance, Out of Tolerance, Unknown)

--- PRELIMINARY CHECKS & WARM-UP ---
[ ] Equipment Serial Number
[ ] Visual Inspection Notes (damage, cleanliness, etc.)
[ ] Power Supply Condition (Nominal, Low, High, Unstable)
[ ] Warm-up Time (minutes)
[ ] Warm-up Start Time
[ ] Initial Readings / Baseline Measurements (before full calibration)
[ ] Equipment Stability Check - Pass/Fail (Pass, Fail)

--- CALIBRATION PROCEDURE ---
[ ] Procedure Step 1: Initial Setting & Zeroing
[ ] Span Adjustment Value (if applicable)
[ ] Zero Adjustment Value (if applicable)
[ ] Calibration Method Used (e.g., Relative, Absolute) (Relative, Absolute, Other (Specify))
[ ] Notes on Procedure Execution (e.g., any deviations from standard)
[ ] Number of Readings Taken
[ ] Calibration Points Used (0% Span, 25% Span, 50% Span, 75% Span, 100% Span, Other (Specify))
[ ] Attach Calibration Graph (if applicable)

--- DATA ACQUISITION & RECORDING ---
[ ] Measurement 1 Reading
[ ] Measurement 2 Reading
[ ] Measurement 3 Reading
[ ] Ambient Temperature (°C)
[ ] Ambient Humidity (%)
[ ] Date of Measurement
[ ] Time of Measurement
[ ] Notes/Observations During Measurement
[ ] Measurement Unit (mm, cm, m, inch)

--- TOLERANCE EVALUATION ---
[ ] Measured Value 1
[ ] Tolerance Upper Limit (Value 1)
[ ] Tolerance Lower Limit (Value 1)
[ ] Result of Value 1 (Within Tolerance?) (Yes, No, Not Applicable)
[ ] Explanation/Comments (if Value 1 is out of tolerance)
[ ] Measured Value 2
[ ] Result of Value 2 (Within Tolerance?) (Yes, No, Not Applicable)
[ ] Explanation/Comments (if Value 2 is out of tolerance)

--- ADJUSTMENT & CORRECTION (IF REQUIRED) ---
[ ] Detailed Description of Adjustment(s) Performed
[ ] Adjustment Value 1 (e.g., Offset)
[ ] Adjustment Value 2 (e.g., Gain)
[ ] Adjustment Method Used (e.g., Software, Manual) (Software Adjustment, Manual Adjustment, Other (Specify))
[ ] If 'Other' selected above, please specify the adjustment method.
[ ] Number of Adjustment Cycles
[ ] Confirmation of Adjustment Stability (Stable after 1 cycle, Stable after 2 cycles, Stable after 3+ cycles, Unstable - Further investigation required)
[ ] Date of Adjustment
[ ] Time of Adjustment
[ ] Technician Signature (Adjustment Confirmation)

--- FINAL VERIFICATION ---
[ ] Span Value (Post-Adjustment)
[ ] Zero Value (Post-Adjustment)
[ ] Linearity Error (Max)
[ ] Repeatability Error (Max)
[ ] Pass/Fail Result (Pass, Fail)
[ ] Comments / Observations (If Applicable)
[ ] Date of Final Verification
[ ] Time of Final Verification
[ ] Technician Signature

--- CALIBRATION CERTIFICATE & DOCUMENTATION ---
[ ] Certificate Number
[ ] Calibration Date
[ ] Next Calibration Due Date
[ ] Equipment Name
[ ] Equipment Model
[ ] Equipment Serial Number
[ ] Calibration Results Summary
[ ] Calibration Data Files
[ ] Calibration Technician Signature

--- EQUIPMENT RETURN & TAGGING ---
[ ] Return Location
[ ] Equipment Tag Number (Pre-Calibration)
[ ] Equipment Tag Number (Post-Calibration)
[ ] Return Date
[ ] Return Time
[ ] Condition Upon Return (Clean, Slightly Dirty, Dirty, Damaged)
[ ] Notes on Return/Condition
[ ] Technician Signature

--- END OF TEMPLATE ---
Transform this text into a digital, automated, and trackable mobile app!
Visit: https://checklistguro.com/templates/facility-management/calibration-checklist
(Click "Install Template" to launch your digital inspection tool immediately)